View MUR220_460158.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MUR220
Preferred Device
SWITCHMODETM Power Rectifier
. . . designed for use in switching power supplies, inverters and as free wheeling diodes, these state- of- the- art devices have the following features:
* * * * *
Ultrafast 25 Nanosecond Recovery Times 175C Operating Junction Temperature Low Forward Voltage Low Leakage Current High Temperature Glass Passivated Junction
http://onsemi.com
Mechanical Characteristics
ULTRAFAST RECTIFIER 2 AMPERES 200 VOLTS
* Case: Epoxy, Molded * Weight: 0.4 gram (approximately) * Finish: All External Surfaces Corrosion Resistant and Terminal * Lead and Mounting Surface Temperature for Soldering Purposes: * * * *
220C Max. for 10 Seconds, 1/16 from case Shipped in plastic bags, 1000 per bag Available Tape and Reeled, 5000 per reel, by adding a "RL'' suffix to the part number Polarity: Cathode Indicated by Polarity Band Marking: MUR220
AXIAL LEAD CASE 059-10 PLASTIC
Leads are Readily Solderable
MAXIMUM RATINGS
Rating Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage Average Rectified Forward Current (Note 1) (Square Wave Mounting Method #3 Per Note 1) Non-Repetitive Peak Surge Current (Surge applied at rated load conditions, halfwave, single phase, 60 Hz) Operating Junction Temperature and Storage Temperature Range Symbol VRRM VRWM VR IF(AV) Value 200 -- 2.0 @ TA = 90C 35 Unit Volts
MARKING DIAGRAM
MUR 220 MUR220 = Device Code
Amps
IFSM
Amps
ORDERING INFORMATION
- 65 to +175 C Device MUR220 MUR220RL Package Axial Lead Axial Lead Shipping 1000 Units/Bag 5000/Tape & Reel
TJ, Tstg
1. Pulse Test: Pulse Width = 300 ms, Duty Cycle 2.0%.
Preferred devices are recommended choices for future use and best overall value.
(c) Semiconductor Components Industries, LLC, 2003
1
April, 2003 - Rev. 4
Publication Order Number: MUR220/D
MUR220
THERMAL CHARACTERISTICS
Characteristic Maximum Thermal Resistance, Junction to Ambient Symbol RqJA Value See Note 1 Unit C/W
ELECTRICAL CHARACTERISTICS
Maximum Instantaneous Forward Voltage (Note 2) (IF = 2.0 Amp, TJ = 150C) (IF = 2.0 Amp, TJ = 25C) Maximum Instantaneous Reverse Current (Note 2) (Rated dc Voltage, TJ = 150C) (Rated dc Voltage, TJ = 25C) Maximum Reverse Recovery Time (IF = 1.0 Amp, di/dt = 50 Amp/ms) (IF = 0.5 Amp, IR = 1.0 Amp, IREC = 0.25 A) Maximum Forward Recovery Time (IF = 1.0 A, di/dt = 100 A/ms, IREC to 1.0 V) 2. Pulse Test: Pulse Width = 300 ms, Duty Cycle 2.0%. 10 10 vF 0.75 0.95 iR 50 2.0 trr 35 25 tfr 25 ns ns mA Volts
I F , INSTANTANEOUS FORWARD CURRENT (AMPS)
VF @ 150C 1.0
I , INSTANTANEOUS FORWARD CURRENT (AMPS) F
VF @ 150C
1.0
125C 75C 25C 0.1 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 VF, INSTANTANEOUS VOLTAGE (VOLTS) 0.1 0.4 0.5 0.6 0.7
125C 75C 25C 0.8 0.9 1.0 1.1 1.2 1.3
VF, INSTANTANEOUS VOLTAGE (VOLTS)
Figure 1. Maximum Forward Voltage
Figure 2. Typical Forward Voltage
http://onsemi.com
2
MUR220
100 IR @ 150C IR, REVERSE CURRENT (m A) IR, REVERSE CURRENT (m A) 10 125C 75C 1.0 25C 0.1 1.0 75C 0.1 25C 0.01 10 IR @ 150C 125C
0.01 20 40 60 80 100 120 140 160 180 200 VR, REVERSE VOLTAGE (VOLTS)
0.001 20 40 60 80 100 120 140 160 180 200 VR, REVERSE VOLTAGE (VOLTS)
Figure 3. Maximum Reverse Current
Figure 4. Typical Reverse Current
IF(AV) , AVERAGE FORWARD CURRENT (AMPS)
5.0
PF(AV) , AVERAGE POWER DISSIPATION (WATTS)
2.0 SQUARE WAVE 1.5 dc
4.0
3.0 dc SQUARE WAVE
1.0
2.0
1.0 0
0.5
0
50
100
150
200
0 0 0.5 1.0 1.5 2.0 2.5 IF(AV), AVERAGE FORWARD CURRENT (AMPS)
TA, AMBIENT TEMPERATURE (C)
Figure 5. Current Derating
Figure 6. Power Dissipation
50 TJ = 25C 30 C, CAPACITANCE (pF) 20
10 7.0 5.0 0 10 20 30 40 50 VR, REVERSE VOLTAGE (VOLTS)
Figure 7. Typical Capacitance
http://onsemi.com
3
MUR220
NOTE 1. - AMBIENT MOUNTING DATA
Data shown for thermal resistance junction to ambient (RqJA) for the mountings shown is to be used as typical guideline values for preliminary engineering or in case the tie point temperature cannot be measured.
TYPICAL VALUES FOR RqJA IN STILL AIR Mounting Method 1 2 RqJA 3 Lead Length, L 1/8 1/4 1/2 52 65 72 67 80 87 50 Units C/W C/W C/W
MOUNTING METHOD 1
L
L
EEEEEEEEEEEE EEEEEEEEEEEE
Vector Pin Mounting MOUNTING METHOD 3
EEEEEEEEEEE EEEEEEEEEEE
MOUNTING METHOD 2
L L
EE EE EE EE EE EE EE
L = 3/8
Board Ground Plane
P.C. Board with 1-1/2 X 1-1/2 Copper Surface
http://onsemi.com
4
MUR220
PACKAGE DIMENSIONS
MINI MOSORB CASE 59-10 ISSUE S
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 59-04 OBSOLETE, NEW STANDARD 59-09. 4. 59-03 OBSOLETE, NEW STANDARD 59-10. 5. ALL RULES AND NOTES ASSOCIATED WITH JEDEC DO-41 OUTLINE SHALL APPLY 6. POLARITY DENOTED BY CATHODE BAND. 7. LEAD DIAMETER NOT CONTROLLED WITHIN F DIMENSION. DIM A B D F K INCHES MIN MAX 0.161 0.205 0.079 0.106 0.028 0.034 --- 0.050 1.000 --- MILLIMETERS MIN MAX 4.10 5.20 2.00 2.70 0.71 0.86 --- 1.27 25.40 ---
B
K F
D
A F K
http://onsemi.com
5
MUR220
SWITCHMODE is a trademark of Semiconductor Components Industries, LLC.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada JAPAN: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative.
http://onsemi.com
6
MUR220/D

▲Up To Search▲

Price & Availability of MUR220

	To Download MUR220 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .